Moxa Technologies NE-4100 Guía de usuario Pagina 1

NE-4100 Series Serial Command Mode User’s Guide www.moxa.com/product First Edition, September 2004 Moxa Technologies Co., Ltd. Tel: +886-

NE-4100 Series Serial Command Mode User’s Guide Page 733 Chapter 3 Operation Flow Chart NOTE 1. This flowchart represents a continual process. Y

NE-4100 Series Serial Command Mode User’s Guide Page 844 Chapter 4 Configuring Serial Command Mode by Entering Trigger Type In this chapter, we exp

NE-4100 Series Serial Command Mode User’s Guide Page 93. Once the NE-4100-CMD is located, click on the product’s Model to highlight it, and then cli

NE-4100 Series Serial Command Mode User’s Guide Page 10NOTE 1. The default setting is HW Trigger Enabled. 2. Only one of the two trigger types (HW

NE-4100 Series Serial Command Mode User’s Guide Page 11Web Console The Network Enabler Web Console provides ready access to NE-4100-CMD via web brows

NE-4100 Series Serial Command Mode User’s Guide Page 123. Modify the Trigger Setting and SW Trigger Character as needed, and then click on Submit.

NE-4100 Series Serial Command Mode User’s Guide Page 1355 Chapter 5 Entering Serial Command Mode In this chapter, we explain how to enter Serial Co

NE-4100 Series Serial Command Mode User’s Guide Page 14Serial Port Parameters The serial port paramters for port P0 can be obtained from Network Enab

NE-4100 Series Serial Command Mode User’s Guide Page 1566 Chapter 6 Exiting Serial Command Mode There are three ways to exit Serial Command Mode. A

NE-4100 Series Serial Command Mode User’s Guide Page 1677 Chapter 7 Determining the Active Mode There are two ways to check if NE-4100-CMD is in Co

NE-4100 Series Serial Command Mode User’s Guide The software described in this manual is furnished under a license agreement and may be used only in

NE-4100 Series Serial Command Mode User’s Guide Page 17By Text via the Serial Port If the NE module is in serial command mode, it will respond with a

NE-4100 Series Serial Command Mode User’s Guide Page 1888 Chapter 8 SW Reset Function Network Enabler Administrator provides an easy way to enable

NE-4100 Series Serial Command Mode User’s Guide Page 1999 Chapter 9 Factory Defaults The factory default settings for the serial port, Ethernet por

NE-4100 Series Serial Command Mode User’s Guide Page 201100 Chapter 10 Demonstration/Testing Environment In this chapter, we give four examples tha

NE-4100 Series Serial Command Mode User’s Guide Page 21Example 1: Get Model Name using HW Trigger STEP 1: Configure trigger mode to HW trigger (Chap

NE-4100 Series Serial Command Mode User’s Guide Page 22Example 3: Get IP Mode using SW Trigger STEP 1: Configure trigger mode to SW trigger, and che

Table of Contents Chapter 1 Introduction ...1 Chap

NE-4100 Series Serial Command Mode User’s Guide Page 111 Chapter 1 Introduction The Serial Command Mode function described in this User’s Guide is

NE-4100 Series Serial Command Mode User’s Guide Page 222 Chapter 2 Serial Command Format and Command Set In this chapter, we describe the structure

NE-4100 Series Serial Command Mode User’s Guide Page 3Reply Code Settings Comments Y Command was executed successfully 1 Command not supported 2

NE-4100 Series Serial Command Mode User’s Guide Page 4OP Code Settings Parameter Device setting Aa | Ap xxx.xxx.xxx.xxx | xxx.xxx.xxx.xxx (e.g., 255

NE-4100 Series Serial Command Mode User’s Guide Page 5OP Code Settings Parameter Device setting C1 0 – 65535 Client Port 1 C2 0 – 65535 Client P

NE-4100 Series Serial Command Mode User’s Guide Page 6OP Code Settings Parameter Device setting UF 0 – 65535 (ms) Force Tx Timeout Digital IO DM