
18-35
www.moxa.com
IP Surveillance >
VPort 364A Series
VPort 364A Series
Excellent video quality, 4-channel H.264/MJPEG industrial
video encoders
The VPort 364A is a 4-channel industrial video encoder that supports
the H.264 video compression algorithm, which uses less bandwidth
than other video compression standards; the VPort 364A provides
the best video quality available on the market today. In addition, the
VPort 364A supports simultaneous dual video streams with different
Introduction
› Dual simultaneous H.264 and MJPEG video streams
› Video latency under 200 ms
› Moxa DynaStream™ function supported for network efficiency
› ONVIF supported for standardization and interoperability
› 802.1X and SSL/SSH for advanced network security
› Industrial design with -40 to 75°C operating temperature
› VPort SDK PLUS provided free
Introduction formats: H.264 and MJPEG. The two video streams can
be used for different purposes, such as viewing, recording, or analysis.
In addition, the rugged industrial design with -40 to 75°C operating
temperature, built-in fiber Ethernet ports, IP30 form factor protection,
and industrial certifications, make the VPort 364A highly suitable for
use in harsh environments.
Specifications
Video
Video Compression: H.264 (MPEG4 part 10, AVC) or MJPEG
Video Inputs: 4, BNC connector (1.0 Vpp, 75 ohm)
Video Streams: Dual streams (one for H.264, the other for MJPEG)
NTSC/PAL: Manual
Video Resolution and FPS (frames per second) in single video
stream:
NTSC PAL
Size Max. FPS Size Max. FPS
QCIF
176 x 112 30 176 x 144 25
CIF
352 x 240 30 352 x 288 25
VGA
640 x 480 30 640 x 480 25
4CIF
704 x 480 30 704 x 576 25
Full D1
720 x 480 30 720 x 576 25
Video Viewing:
• DynaStream™ supported for changing the video frame rate
automatically
• Adjustable image size and quality
• Timestamp and text overlay
Audio
Audio Inputs: 1, Line-in or MIC-in with RCA connector
Audio Outputs: 1, Line-out with RCA connector
Audio Format: Mono, PCM
Network
Protocols: TCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, UPnP,
RTP, RTSP, ICMP, IGMPv3, QoS, SNMPv1/v2c/v3, DDNS, Modbus/
TCP, 802.1X (Pending), SSL/SSH (Pending)
Ethernet: 1 10/100BaseT(X) auto negotiating RJ45 port, or 1
100BaseFX fiber port (single/multi-mode, SC connector)
Serial Port
PTZ Ports: 1, RS-232/422/485 port (5-pin terminal block connector),
max. speed of 115.2 Kbps
Console Port: 1, RS-232 RJ45 port
GPIO
Digital Inputs: 4, max. 8 mA
Low: +13 V to +30 V; High: -30 V to +3 V
Relay Outputs: 2, max. 24 VDC @ 1 A
LED Indicators
STAT: System status
PWR1: Power 1
PWR2: Power 2
FAULT: Can be configured to correspond to system alarm, power
failure, or disconnected network
V1, V2, V3, V4: Video input signal activity for channels 1 to 4
Power Requirements
Input Voltage: 2 12 VDC or 24 VDC/VAC inputs for redundancy,
terminal block connector
Power Consumption: Max. 7.5 W
Physical Characteristics
Housing: Metal, IP30 protection
Dimensions: 80.2 x 135 x 105 mm (3.16 x 5.31 x 4.13 in)
Weight: 1110 g
Installation: DIN rail mounting or panel mounting (with optional
mounting kit)
Alarms
Video Motion Detection: Includes sensitivity tuning
Video Loss: Video loss alarm
Scheduling: Daily repeat timing schedule
Imaging: JPEG snapshots for pre/trigger/post alarm images
Email/FTP Messaging: Automatic transfer of stored images via email
or FTP with event-triggered actions
Comentarios a estos manuales